So, any speed over 200mm/sec causes this skew. Doesn't matter the power. All other settings staryed the same. In the picture the"why" on the left was at 201mm/sec and the one on the right was at 200. I did multiple speeds and anything above 200 did this. It did this with boxes also.
Anyone have some suggestions?
Things are askew
-
Benjamin Trinkle
- Posts: 8
- Joined: Wed Mar 06, 2019
- Location: Southern Illinois
- Country: United States
- Laser Machine Make or Type: Chinese
- Laser Power: 50w
- Laser Bed Size: 12x20
- Home Position: TL
- RDWorks Version: dont use
- Windows Version: 7-10
You do not have the required permissions to view the files attached to this post.
-
Gene Uselman
- Posts: 2180
- Joined: Thu Jul 07, 2016
- Location: Suburban Minneapolis, Minnesota, US
- Country: USA
- Nickname: Gene
- Laser Machine Make or Type: QC
- Laser Power: 130W
- Laser Bed Size: 900x1300
- Home Position: TR
- Control Software: LIGHTBURN
- RDWorks Version: RDw .19 & Lightburn
- LightBurn Version: Latest
- Ruida Controller: RDC6442
- Windows Version: Win 10 Pro
- Accessories: I have a combining lenses, pin tables [homebuilt], honeycomb tables , wireless remote, Modifed Ultimate Air Assist, home built non-powered rotary device, PrusaMK4 and Mini Prusa printers.
Are you using Lightburn software? I have never seen this particular behavior with RDworks,
If the Help and advice you received here was of VALUE...
Please consider making a donation to maintain the RDWORKSLAB Forum.
The days that I keep my gratitude higher than
my expectations, Well, I have really good days.
Ray Wylie Hubbard- unfortunately deceased
Please consider making a donation to maintain the RDWORKSLAB Forum.
The days that I keep my gratitude higher than
my expectations, Well, I have really good days.
Ray Wylie Hubbard- unfortunately deceased
-
Benjamin Trinkle
- Posts: 8
- Joined: Wed Mar 06, 2019
- Location: Southern Illinois
- Country: United States
- Laser Machine Make or Type: Chinese
- Laser Power: 50w
- Laser Bed Size: 12x20
- Home Position: TL
- RDWorks Version: dont use
- Windows Version: 7-10
Yes I am using lightburn. I might try Rd works on Monday to see if I can replicate it.Gene Uselman wrote: Fri Mar 08, 2019 Are you using Lightburn software? I have never seen this particular behavior with RDworks,
-
Benjamin Trinkle
- Posts: 8
- Joined: Wed Mar 06, 2019
- Location: Southern Illinois
- Country: United States
- Laser Machine Make or Type: Chinese
- Laser Power: 50w
- Laser Bed Size: 12x20
- Home Position: TL
- RDWorks Version: dont use
- Windows Version: 7-10
Edit:. I forgot to mention, it also only does it when bi-directional scanning is off. Works fine when it's on with any speed.
-
Gene Uselman
- Posts: 2180
- Joined: Thu Jul 07, 2016
- Location: Suburban Minneapolis, Minnesota, US
- Country: USA
- Nickname: Gene
- Laser Machine Make or Type: QC
- Laser Power: 130W
- Laser Bed Size: 900x1300
- Home Position: TR
- Control Software: LIGHTBURN
- RDWorks Version: RDw .19 & Lightburn
- LightBurn Version: Latest
- Ruida Controller: RDC6442
- Windows Version: Win 10 Pro
- Accessories: I have a combining lenses, pin tables [homebuilt], honeycomb tables , wireless remote, Modifed Ultimate Air Assist, home built non-powered rotary device, PrusaMK4 and Mini Prusa printers.
Please post your results with RDworks, I am sure that the OZ from LB will be interested too.
If the Help and advice you received here was of VALUE...
Please consider making a donation to maintain the RDWORKSLAB Forum.
The days that I keep my gratitude higher than
my expectations, Well, I have really good days.
Ray Wylie Hubbard- unfortunately deceased
Please consider making a donation to maintain the RDWORKSLAB Forum.
The days that I keep my gratitude higher than
my expectations, Well, I have really good days.
Ray Wylie Hubbard- unfortunately deceased